• Bienvenidos al Foro de automecanico.com. Crea tu mensaje y especifica modelo de auto o vehiculo, tipo de motor, transmision y sintomas de su problema o falla. Aprendemos de las experiencias de mecanica automotriz de todos.

Diagrama Banda De Tiempo Honda Civic 1.6

GREGORY

Nuevo Miembro
Buenas Tardes Necesito El Diagrama De La Puesta A Tiempo Para Un Honda Civic 1.6 Año 1994 ( 16 Valvulas).
 

carloz

Experto
hola aimgo espero esto sea de tu ayuda. !Saludos y suerte!!
 

Adjuntos

  • timing honda camshaft.jpg
    timing honda camshaft.jpg
    71,8 KB · Visitas: 4.388
  • timing honda crankshaft.jpg
    timing honda crankshaft.jpg
    107 KB · Visitas: 4.026

Tobe82

Experto
Hola, puede que esta info ayude a quien la ocupe
Banda de tiempo para
1992-95 CIVIC & 1993-95 DEL SOL 1.6L motor D16Z6

This engine is classified as an Interference engine. If the timing belt breaks or jumps timing, a piston may contact an open valve. Piston to valve contact may cause damage to the valve, piston and other engine components. In some cases valve to valve contact may be experienced when the timing belt breaks or jumps timing. To avoid belt breakage, replace the timing belt as recommended by the vehicle manufacturer timing belt replacement interval.
With the timing belt removed, avoid turning the camshaft or crankshaft. If movement is required, exercise extreme caution to avoid valve damage caused by piston contact.
1.Disconnect and isolate the battery ground cable.
2.Remove the splash shield, then the power steering pump and set aside. Do not disconnect the power steering hoses.
3.Remove the A/C compressor adjuster pulley with bracket and the A/C belt, if equipped, then the alternator belt.
4.Remove the power steering pump bracket, cruise control actuator.
5.On Civic models, proceed as follows:
a.Remove the power steering tank bracket.
b.Remove the engine support nuts, then loosen the mount bolt.
c.Pivot the engine side mount rubber aside.
6.On del Sol models, proceed as follow: support the engine by positioning a suitable jack and wooden block under the engine oil pan. Remove the three upper engine mounting bracket retaining nuts, then the bracket.
a.Support the engine by positioning a suitable jack and wooden block under the engine oil pan.
b.Remove the three upper engine mounting bracket retaining nuts, then the bracket.
c.Remove the cylinder head cover, then the upper timing belt cover.
7.On all models, remove the crankshaft pulley, then remove the timing belt upper and lower covers, Fig. 1.
8.Loosen the timing belt tensioner adjuster bolt by 1/2 turn. Rotate the timing belt tensioner until tension is released from the timing belt. Temporarily tighten the timing belt tensioner in this position.
9.Ensure the No. 1 piston is at TDC on the compression stroke and the camshaft sprocket is aligned, Fig. 2.
10.Remove the timing belt.
11.Install the new timing belt in sequence, Fig. 3, then loosen the timing belt tensioner adjusting bolt by 1/2 turn. The tensioner will rotate, applying tension to the timing belt. Tighten the tensioner adjusting bolt.
12.Rotate the crankshaft 4-6 turns counterclockwise to seat the timing belt on the sprockets.
13.Adjust the timing belt tension as follows:
a.Temporarily install the crankshaft pulley and bolt. Torque the pulley bolt to 134 ft. lbs.
b.Rotate the crankshaft counterclockwise 3 teeth to create tension on the timing belt. Ensure the timing belt and the camshaft sprocket are securely engaged, then torque the timing belt tensioner adjustment bolt to 33 ft. lbs.
c.Ensure the crankshaft and camshaft sprockets are at TDC.
14.Remove the crankshaft pulley, then install the timing belt upper and lower covers. Torque the cover bolts to 84 inch lbs.
15.Install the crankshaft pulley and bolt. Torque the pulley bolt to 134 ft. lbs.
16.Install the cylinder head cover. Torque the nuts to 84 inch lbs.
17.Install the engine support bolt and nuts. Torque the bolts and nuts to 38 ft. lbs. Torque the through bolt to 54 ft. lbs.
18.On del Sol models, lower the jack positioned under the oil pan.
19.On all models, install the cruise control actuator and the power steering tank bracket.
20.Install the power steering bracket. Torque the bolts to 33 ft. lbs.
21.Install the alternator belt, then the A/C belt and the A/C compressor adjuster pulley with bracket. Torque the A/C compressor adjuster pulley bolts to 17 ft. lbs. Refer to "Accessory Drive Belt Tension" for proper belt tension.
22.Install the power steering pump. Torque the upper bolt to 33 ft. lbs. and the lower bolt to 17 ft. lbs.
23.Install the splash shield.
24.Connect the battery ground cable.
 

Adjuntos

  • honda-civic-timingbelt1.jpg
    honda-civic-timingbelt1.jpg
    123,2 KB · Visitas: 9.507
  • honda-civic-timingbelt2.jpg
    honda-civic-timingbelt2.jpg
    53,7 KB · Visitas: 1.297
  • honda-civic-timingbelt3.jpg
    honda-civic-timingbelt3.jpg
    70 KB · Visitas: 2.768
Arriba